glue bond
英 [ɡluː bɒnd]
美 [ɡluː bɑːnd]
胶（结）合剂
双语例句
- This new glue makes a firmer bond.
这新胶水粘的牢。 - The Design and Application of the Groove-Making Mould for Glue Bond Strength Test Pieces
胶合强度试件制槽模具的设计与应用 - When the glue has set, the bond formed is watertight.
胶水凝结后形成的黏台将是不透水的。 - Plywood& Determination of glue bond strength
GB/T9846.12-1988胶合板胶合强度的测定 - The glue on the tape is a wonderful adhesive agent and will bond well to anything from a piece of crystal to the handle of a broom.
这种带子的粘胶是一种极好的粘合剂，它能牢固地粘接到任何东西上，不论是一块水晶还是一个扫帚把。 - Especially on slow curing speed and unideal glue bond properties UF resin with low molar ratio, it can solved by synthesis technology, modifier and different curing system.
特别是针对通常情况下低F/U摩尔比UF树脂固化速度慢、胶接性能不理想的问题，可以通过合成工艺和改性剂以及不同固化体系得以解决。 - The result indicates that YJ 302 bond has the interface felt more strongly than the cement slurry and the 107 glue cement slurry when the old pavement is not chiseled. The YJ 302 provides the pavement to be bond well and makes the pavement be combine entirety.
结果表明，YJ-302不凿毛时的界面粘结力高于水泥净浆和107胶水泥浆，能保证道面获得较好的粘结力，使道面完全结合。 - Glue bond strength increased too while the final ratio of UF increased.
胶合强度随终摩尔比的增大而增大； - Study on the curing mechanism and glue bond properties in different curing system of three typical UF resin with low FE of different synthesis technology and modification means, it revealed curing characteristics of UF resin with low FE.
本论文通过研究不同合成工艺、不同改性方法所合成的3种典型低甲醛释放UF树脂在不同固化反应体系条件下的固化反应机理和胶接性能，揭示了低甲醛释放UF树脂的固化特性。 - BW rubber expander glue bond substitutes for stepped joint or tongued and grooved joint in the horizontal joint site on the outside wall of basement.
在地下室外墙施工中，铺设BW温水膨胀橡胶止水条，取代了水平接缝处留阶梯缝或凸凹缝的作法； - The glue made from seeds of pigeonpea-a fast-growing shrub was substituted for soybean glue in the study. The test results showed that the bond strength of the plywood reached or surpassed National standard GB 9846-88.
采用速生灌木树种木豆的种子代替大豆制成豆胶用于压制胶合板，其胶合强度达到或超过GB984688的规定。 - The results of microscopic observation on the glue line and internal bond testing of the board showed that the condensed water would dilute PF and thus increase its flow and penetration into flakes.
通过显微观察及板内结合强度测试，结果表明，蒸汽冷凝水对水溶性PF树脂胶有稀释作用，改变胶的流动和渗透性能。 - When the glue spread is same, the bond strength decreases with the increase of the veneer thickness.
在涂胶量相同情况下，随着单板厚度增加，胶合强度降低。 - Form the Pt electrode in glass substrate using dry etching. And then dump a layer of PDMS glue on the top of platinum electrode, and bond with the PDMS cover. 3.
采用干法刻蚀，在玻璃基板上形成了Pt电极，然后在铂电极上甩了一层PDMS胶，与上盖片进行了键合。 - When the glue spread reached some value, the bond strength gets stable or decreases slightly.
随着涂胶量增大，胶合板的胶合强度增大，当达到某一值之后，趋于稳定或略有下降。